Product ID:REMTEK HEAT-SHRINKABLE POLYMERIC PRODUCTS(S
MSDS Date:04/01/1991
FSC:9330
NIIN:00N038945
MSDS Number: BRHRP

RAYCHEM CORP

300 CONSTITUTION DR
MENLO PARK, CA 94025
US

Emergency Phone: 415-361-4907

Info Phone: 415-361-4907

Preparer: DONNA SEID/FRED SMITH

Cage: 06090

RAYCHEM CORP

MENLO PARK, CA 94025-1164 US

Telephone: 415-361-4907

Cage: 06090

RETARDED PRODUCTS. DISPOSAL MUST BE IN ACCORDANCE

RTECS: 9999999ZZ

INSTALLATION INSTRUCTIONS & APPLICATION GUIDES

RTECS: 9999999ZZ

ENSURE THAT ANY LOCAL REQUIREMENTS/LEGISLATION

RTECS: 9999999ZZ

WHEN USING IR (INFRARED) HEATING DEVICES, OBSERVE

RTECS: 9999999ZZ

SURFACES ON INSTALLATION EQUIPMENT.

RTECS: 9999999ZZ

BASE POLYMER MATERIALS INCLUDING INGREDIENTS 2-8 & MAY BE

RTECS: 9999999ZZ

POLYETHYLENE AS A COPOLYMER; (POLYETHYLENE COPOLYMERS)

OSHA PEL N/K

ACGIH TLV: N/K

OLEFIN COPOLYMERS

OSHA PEL N/K

ACGIH TLV: N/K

FLUOROPOLYMERS

OSHA PEL N/K

ACGIH TLV: N/K

CHLOROPOLYMERS

OSHA PEL N/K

ACGIH TLV: N/K

POLYAMIDES

OSHA PEL N/K

ACGIH TLV: N/K

POLYESTERS

OSHA PEL N/K

ACGIH TLV: N/K

SILICONES

OSHA PEL N/K

ACGIH TLV: N/K

ADHESIVE; (ADHESIVES/MASTICS)

OSHA PEL N/K

ACGIH TLV: N/K

BURNS, THERMAL DEGRADATION BYPRODUCTS WILL

RTECS: 9999999ZZ

LIMITED TO, CARBON MONOXIDE, CARBON DIOXIDE,

RTECS: 9999999ZZ

SILICON DIOXIDE, HYDROGEN CHLORIDE, HYDROGEN

RTECS: 9999999ZZ

NITROGEN, PHOSPHORUS, & SULFUR.

RTECS: 9999999ZZ

ZEROHAL, PRODS WILL BE SUBJECT TO SUCH REGS.

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:IN COMMON W/MOST ORGANIC MATLS,
DEGRADATION & COMBUSTION BYPRODUCTS MAY BE TOXIC AND SHOULD NOT BE
INHALED. (SEE DECOMPOSITION PRODUCTS SECTION FOR MORE SPECIFIC
INFO.) OVERHEATING THE PRODUCT TO CHAR RING OR BURNING WILL PRODUCE
FUMES THATMAY CAUSE EYE, SKIN, NOSE & THROAT IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:EYES:IF EYE IRRIT OCCURS, FLUSH W/WATER FOR @ LST 15 MIN.
SEEK MED ATTN. SKIN:IF MOLTEN ADHESIVE/MASTIC CONTACTS SKIN, COOL
IMMED IN WATER. DO NOT ATTEMPT TO REMOVE MATERIAL FROM THE SKIN-
TREAT AS A BURN AND SEEK MEDICAL ATTENTION. INGEST: NOT A NORMAL
ROUTE OF EXPOSURE. IF SWALLOWED, SEEK MED ATTN. INHAL: REMOVE TO
FRESH AIR. SEEK MED ATTN IF ANY BRTHG PROBLEMS DEVELOP.

Extinguishing Media:CARBON DIOXIDE, WATER, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:TOXIC FUMES MAY EVOLVE IN A FIRE. FIREFIGHTERS
SHOULD WEAR NIOSH/MSHA APPROVED SCBA & FULL PROTECTIVE EQUIPMENT
IN ENCLOSED AREAS.
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.

Spill Release Procedures:NONE SPECIFIED BY MANUFACTURER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:AVOID HEATING PRODS BEYOND TEMP
REQUIRED FOR NORMAL INSTALLATION. SEE INSTALLATION INSTRUCTIONS FOR
PROPER INSTALLATION PROCEDURES.
Other Precautions:IF PROD CHAR OR BURN, IMMEDIATELY STOP HEATING. AVOID
INHALING ANY FUMES WHICH MAY EVOLVE UNDER SUCH CIRCUMSTANCES. ALLOW
ANY FUMES TO DISPERSE AND VENT BEFORE CONTINUING WORK IN THE AREA.
INSTALLATIO N: FOLLOW APPROP RAYCHEM (ING 16)

Respiratory Protection:NIOSH/MSHA APPROVED RESPIRATORS ARE RECOMMENDED
IF INSTALLATION OCCURS IN CONFINED UNVENTILATED AREA.
Ventilation:I/A/W GOOD INDUST HYGIENE PRACTICE, ENSURE VENT ADEQUATE TO
CONTROL EXPOSURE BELOW STATE & FED PEL DURING INSTALLATION.
Protective Gloves:HEAT-RESISTANT GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
MFR TRADE NAME/PART NO: (EXCLUDING SOLDER SLEEVES - SEE SEPARATE MSDS).
DECOMP PRODS: DEGRADATION IS NOT SIGNIFICANT AT TEMPERATURE
ACHIEVED DURING PROPER INSTALLATION, AS DIRECTED BY PRODUCT
INSTALLA TION GUIDES. AT TEMPS HIGHER THAN THOSERECOMMENDED FOR
PROPER INSTALLATION, MOST SIGNIFICANTLY IF THE PROD (ING 10)

Appearance and Odor:PLASTIC TUBING & MOLDED PARTS IN A VARIETY OF
SHAPES, SIZES & COLORS. NO ODOR.

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:AVOID OVERHEATING OF PRODUCT.
Hazardous Decomposition Products:IN COMMON W/MOST ORGANIC MATLS,
DEGRADATION & COMBUST BYPROD MAY BE TOXIC & SHLD NOT BE INHALED.
THERMAL (SUPP DATA)

Waste Disposal Methods:ALL PRODS ARE CLASSIFIED AS NON-HAZ WASTE & SHLD
BE BURIED OR INCINERATED AT APPROVED SITES. IF THERE ARE LOCAL REGS
COVERING THE CONTROLLED INCINERATION OF HALOGENATED MATLS, THEN ALL
FLAME-RETARDED PRODUCTS, W/THE EXCEPTION OF (ING 14)

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.